日本大雅迪克伺服电动缸SCN6-060-300-B

System model			SCN6-060-050/100/150/200/250/300-B
Stroke (mm)			50	100	150	200	250	300
Maximum thrust (N)/(kgf):			650 / 66.3 (Typical value)
Maximum payload when power is turned on (vertical use) (kg)			45
Maximum thrust in push mode (N)/(kgf):typ			450 / 45.9
Maximum speed (mm/s)			100 (Typical value at 25℃)
Repeatable positioning accuracy (mm)			±0.01 (Short-time repeatable positioning accuracy） Note 1), Note 2)
Lost motion (mm)			0.3
Allowable radial load (N)			30	20	10	10	10	10
Rod diameter (mm)			φ22
Rod tip screw diameter			M14 Pitch1.5（SUS303）
Number of positioning points			16
Power supply			DC24V±10 % (Power supply: max. 3.0 A, Control circuit power supply: max. 0.2 A)
Input/output signal	parallel input signal	Signal name	DC24V DI/DO interface (connector PIO), Target position number (4-bit binary: PC1, PC2, PC4, PC8), start (CSTR), Axis movement interlock (ILK)
		input current	Max 4mA/port (Please connect with sink type output circuit)
	parallel output signal	Signal name	DC24V DI/DO interface (connector PIO), completed position number (4-bit binary: PC1, PC2, PC4, PC8), positioning complete (PFIN), alarm (ALM), zone signal (ZONE), home return complete (ZFIN) )
		Output current	Maximum 10mA/port (open collector output)
	serial signal		Serial interface (connector SIO) +5V、5G、S+、S-
Protection function			Overspeed, main power overvoltage, regenerative voltage abnormality, overload, sensor abnormality,servo abnormality, encoder disconnection
Environmental condition	Operating temperature		0 ～ 40 ℃ [Amp： 0 ～ 55 ℃ ]
	storage temperature		-20 ～ 60 ℃ [Amp：　-20 ～ 60 ℃ ]
	Usage/storage humidity		≦ 90% RH, but no condensation [Amp: 20～80 % RH or less, no condensation]
	protective structure		IP-40 equivalent
	Vibration/Shockproof		2G / 10G (2 times) [Amplifier: 0.5G / 2G (3 times)]
Cylinder weight (kg)			1.9	2.2	2.5	2.8	3.1	3.4
Servo amplifier weight (kg)			0.4

※）	Due to product improvement, some ratings, specifications, dimensions, etc. may be changed without notice
Note(1)	Urethane rubber (Shore 90) for home positioning is used at both stroke ends of the electric cylinder. The aging of urethane rubber is estimated to be a maximum of 0.05 to 0.07 mm/1 to 2 years. Therefore, it is possible that the origin position may shift by up to 0.07mm due to changes over time, so processing such as data correction may be required depending on the user's usage. In addition, the home position when shipped from the factory is the backward end (motor side) home position. When using the home position on the forward end side (opposite the motor side), change it using the teaching tool.
Note(2)	Positioning is done from one direction

　SCN6-060-□□□-B (NPN specifications)
External connection diagram

SCN6 series wiring diagram

上一篇：日本大雅迪克机械气缸SCN6-050-050-B-M 下一篇：日本大雅迪克控制器RAD2311-A01-NA

返回列表